Accessories

  • Solar Battery Charger

    We offer a 2 watt solar charger to help maintain your battery for dump trailers and tilt trailers.

    These work well in conjunction with our integrated battery charger.

    The panel is protected by a clear polyurethane coating that makes them extremely durable and weather proof.

    This panel has a 5 year limited warranty.

Get a Quote

  • Cargo Tie Down Loops

    Our utility trailers come with stake pockets standard but some users prefer to use tie-down loops that sit above the deck. These are great for strapping four wheelers, UTVs, motorcycles, mowers, and other cargo. The cargo tie-down loops are sold in pairs, with two pair (4 loops) being the most common.

    • Rated at 1000 lbs capacity
    • Loops angled at 45 degrees
    • Loops mounted on top of the outside frame
    • Standard on expanded metal and solid sides
    • Option code: -TD01 (2 loops), -TD02 (4 loops), -TD03 (6 loops), etc.
Get a Quote

  • Bolt On Chain Rack

    Features

    • Rack stores up to 5 chains
    • Bolts to c-channel behind risers and front gussets on PJ gooseneck trailers
    • Can be locked to help prevent theft
    • Can be mounted to driver or passenger side (two racks recommended for chains & boomers)
    • Fit FS, FD, LD, FY, LY, & SD models
Get a Quote

  • Wireless Remote For Trailers

    One of the most popular additions for dump trailers, tilt trailers, hydraulic jacks, and winches are wireless remotes.

    They make operating trailer hydraulics extremely convenient and fast.

    Our wireless remote is built by the same manufacturer as our hydraulic pump, so it is truly a "plug and play" installation.

    To install, simply separate the quick connector from the corded controller and tee in the matching connectors from the wireless.

    Hook up the positive and negative power feeds to the battery and attach the external antenna to the outside of the toolbox and you are ready to go.

    • Easy plug and play installation
    • Equipped with an 15 amp fuse to protect against electrical overload
    • 20 minute sleep program for safety, to prevent accidental operation or unauthorized use
    • Is not compatible with gravity down pumps or pumps with 4 way pendants
    • PJ Part: 190101
Get a Quote

  • Bolt On Light Bar

    Do you want to load and unload your trailer at night?

    Check out our easy to install bolt-on light bar.

    This light bar features four (4) round utility lights that give you ample lighting and installs in around 30 minutes.

    Pre-wired & ready to bolt-on - lights are included

    • Fits on the channel cross-members between the risers on any PJ Gooseneck
    • Includes four (4) round utility lights in a shock proof rubber housing
    • Lights can be adjusted vertically and horizontally
    • 1 1/2" mandrel bent round tube protective bar, lower frame built from 3/16" powder coated steel
    • Pre-wired with generous 9ft of wiring for simple two-wire installation (includes automotive inline fuse)
    • Toggle switch is mounted to light bar, for easy access from the trailer deck or ground
    • Lights are wired to junction box and powered by tow vehicle
    • Lights are connected with heat shrink butt connectors for protection and reliability (see photos)
    • Wiring for each light is protected by angle conduit (see photos)
    • Includes zinc plated hardware (nuts, washers, & bolts) and instructions for installation
    • Tools required for installation: Cordless Drill, 3/8" Drill Bit, 1/2" Wrench, Screwdriver, and Pliers
    • Light bar dimensions: 42" wide x 12.5" tall x 4" deep - Weight: 26 lbs
    • If ordered with a top riser toolbox the light bar must be mounted forward on the neck on top of the I-beam

    Available colors

    • Black: PJ Part: 170126
    • Red: PJ Part: 170129
    • Grey: PJ Part: 170130
    • White: PJ Part: 170131
    • Yellow: PJ Part: 170132

Installation Instructions

Estimated Installation Time:

  • Novice (1 hour)
  • Expert (30 minutes or less)

Tools Required:

  • Cordless Drill
  • 3/8" or 1/2" Drill Bit
  • 1/2" Open Wrench
  • 1/2" Ratcheting Socket Wrench
  • 1/4" Socket
  • Phillips Screwdriver
  • Pliers

Mark the center point on the rear c-channel cross-member between the risers of the gooseneck.

Mark the center point on the light bar (42" wide) and align light bar in center of cross-member.

Make sure light bar is positioned in desired location. Carefully mark the position of the holes on the light bar on the cross-member.

Using a 3/8" drill bit (or larger), drill two holes through the cross-member on marks made in previous step.

Tip: Use a smaller bit to create "pilot hole" before drilling your final holes.

Place light bar on to cross-member and insert bolts into their holes. Install supplied bolts & washers on each side using 1/2" wrench (Using a ratcheting socket on top bolt and open end wrench on lower nut works best).

Optional: Route wiring inside of conduit gooseneck using an electrician's snake for maximum protection. If you don't have a snake to run the wiring, you can "zip tie" the wiring along the inside frame of the gooseneck.

Pull wire through to junction box and trim at desired length. Splice cable exposing the positive wire (black) and ground wire (white).

Open the junction box by removing two screws with a phillips screwdriver.

Using a 1/4 socket, install white wire (negative) on to blue post (ground). You can add an optional ring terminal for cleanest installation. Install the included short black wire lead with fuse (positive) on to red post (hot).

Trim black wire (positive) from light bar back to desired length in preparation for inline fuse & wire to be installed.

Place inline fuse over wire from light bar, then crimp the fuse holder using pliers.

Replace cover on junction box and hook up trailer to towing vehicle. With the ignition in the towing vehicle on, switch toggle switch to on position to test lights.

Get a Quote

  • Stake Pocket Spare Tire Mount (Removable)

    Features

    Want to add a Spare Tire Mount to your PJ Trailer but don't want to weld it to the frame? Our stake pocket spare tire mount bolts on in less than a minute. If you like this accessory you might also like our Stake Pocket D-rings.

    • Fits PJ 5 on 5, 6 on 5.5, and 8 on 6.5 bolt patterns
    • Takes less than a minute to install
    • Made from 1/4" smooth plate and 2" x 2" rectangular tubing
    • Black Powder Coat Finish
    • Drive-in studs must be added depending on wheel size (Available at PJ Dealers or through PJ Parts.)
    • Fit most PJ Trailers with 5", 6", or 8" outside frame (channel or tube)
    • Not for use on dump trailer stake pockets
    • Fits the rear stake pocket on PJ utility trailers but doesn't fit the front due to interference with the tongue.
    • PJ Part Number: 160438
Get a Quote

  • Stake Pocket D-rings

    Ever wish you could move your d-rings to different positions around your trailer depending what you were hauling? If so, our stake pocket d-rings make a great addition to any PJ Trailer with our 3 3/4" inside diameter stake pockets. You can simply slide the channel inside the stake pocket and insert the hitch pin.

    • Fits PJ 3 3/4" ID Stake Pockets
    • D-ring rated at 11,780 lbs
    • Can be moved in seconds with no tools
    • Black Powder Coat Finish
    • Includes hitch pin
    • Not for use on dump trailer stake pockets
    • Stake Pocket D-rings do not fit most C4 Carhauler or Utility Trailers (Use Utility D-ring instead)
    • PJ Part Number: 180080

  • Utilty Stake Pocket D-ring

    We have developed a utility trailer version of our extremely popular stake pocket d-rings. This version uses a lighter d-ring and has a notch cut to clear the wrap tongue on a PJ utility trailer and 4" Channel Carhauler.

    • Fits PJ utility trailers and 4" Channel Carhauler
    • Channel is notched to clear trailer tongue
    • D-ring rated at 2,000 lbs
    • Can be moved in seconds with no tools
    • Black Powder Coat Finish
    • Includes hitch pin
    • PJ Part Number: 180078
Get a Quote

  • Product Features

    Features

    Our Bargman cold weather wiring harness keeps your trailer plug flexible and functional in the most extreme weather conditions.

    • 7-way Bargman Plug with Dual Contacts
    • Operating temperature range -67°F to 221°F (-55°C to 105°C)
    • Available in 7 ft bumperpull and 10 ft gooseneck lengths
    • Easy to add to any PJ Trailer with a junction box
    • Part Numbers: 7 ft - 170293 & 10 ft - 170292
Get a Quote

  • Stainless Steel Wheel Simulators

    One of the most popular additions for dump trailers, tilt trailers, hydraulic jacks, and winches are wireless remotes.

    They make operating trailer hydraulics extremely convenient and fast.

    Our wireless remote is built by the same manufacturer as our hydraulic pump, so it is truly a "plug and play" installation.

    To install, simply separate the quick connector from the corded controller and tee in the matching connectors from the wireless.

    Hook up the positive and negative power feeds to the battery and attach the external antenna to the outside of the toolbox and you are ready to go.

    • Easy plug & play installation
    • Equipped with an 15 amp fuse to protect against electrical overload
    • 20 minute sleep program for safety, to prevent accidental operation or unauthorized use
    • Is not compatible with gravity down pumps or pumps with 4 way pendants
    • PJ Part # 190101
Get a Quote